Hello iCandy fans! I’m Cherie from you & mie and I’m really excited to be here with you today! When Jen contacted me to be a part of this great series, I seriously thought it was the most brilliant idea. If you have a great bodice pattern and some ideas for mixing it up, you can pretty much make anything!
And now that we’re getting close to the end of the series and you’re all pros at altering bodice patterns ( 😉 right?), I’ve got something fun for you.
A reversible coat!
It’s going to take a bit of pattern altering, of course, but I’ll walk you through it and it’ll be pretty simple!
And the finished product will be a sweet and practical coat for your little one! I used 2 lightweight fabrics (nani iro double gauze and linen) to make a spring coat since I know our weather will be warming up soon.
– 2 fabrics (yardage will depend on size you’re making)
– 4 buttons (or as many as you desire, just be sure they are the same size and you have enough for both sides of the coat)
– interfacing (optional)
– bodice pattern
– sleeve pattern (or draft your own)
– tracing paper
I started out with Made by Rae’s Geranium Dress pattern for my bodice because it’s the pattern I’ve been using for dresses recently. I went up one size because this is outerwear and I want it to fit over clothes, so instead of a 2T (which my daughter is), I cut out the 3T size bodice pattern.
The original pattern has the front bodice piece cut on the fold and a button placket in the back, but we want our button placket in the front and will cut our back piece on the fold. So, the first step is to cut the extra off the back bodice. Place the front bodice pattern on top of the back bodice pattern lining up the bottom of the armhole and bodice. Mark the fold line onto the back pattern and cut on the line.
Depending on your bodice pattern, you may want to lower the bottom of the armhole. I trimmed off a bit starting from half an inch down.
On your tracing paper, line up the straight edge of your back pattern piece with the edge of your paper and trace the shoulder seam and armhole. I raised the neckline so it hit about an inch higher at the fold line.
From the bottom of the armhole, use a ruler to make an A-line shape for your coat. You can make it whatever length you want. The bottom hemline is slightly curved.
For the front pattern piece, you’ll want to take another piece of tracing paper and tape it so it hangs over the straight edge of the back coat pattern by 1.5 inches (1/2 an inch for seam allowance and another 1 inch for the button placket). Place the front bodice pattern to top so that the bottom of the armhole and the straight edge lines up with the back piece. Trace the shoulder seam and armhole of the bodice pattern. I brought the neckline up by about 1/2 an inch.
Remove the bodice pattern and trace the side seam and bottom hemline from the back pattern piece. Make sense?
Here’s what my pattern pieces looked like.
You’ll also need to draft a sleeve, collar and pocket pattern. For the sleeve, I actually used one that I already had. To make sure it’d fit, I cut a muslin of the sleeve piece and after I sewed the front and back pieces together of the coat, I checked to see if it would fit in the armhole, then adjusted the pattern as necessary. If you don’t have a pattern piece for a sleeve, you can find many tutorials for drafting your own with a simple web search.
From Fabric A, you’ll need:
– 2 front pieces
– 1 back piece (cut on the fold)
– 1 collar piece
– 2 sleeves
– 4 pockets
And from Fabric B, you’ll need the exact same thing!
Now we get to the sewing part!
*If you are using super thin or flimsy fabric, you may want to fuse interfacing to one or both of the collar pieces to add more structure. I did not.*
Place your collar pieces down (1 from Fabric A and 1 from Fabric B) with right sides together. Pin and sew the outer edge. Clip rounded edges to reduce bulk when you flip the collar right side out.
Flip right side out and press flat. Top stitch around the outer edge, if desired.
Place two pocket pieces together (right sides together) and pin. Sew around the edge, leaving a 1 inch opening. I like to sew along the opening as well because it helps flip the seam allowance in when you turn the pocket right side out.
Flip the pocket right side out, press flat and sew onto one of the front coat pieces. Stitch close to the curved edge of the pocket, back stitching several times at the tops of the pocket to reinforce the corners (don’t sew the pocket closed!) Repeat with the other 2 pocket pieces for Fabric A.
*Again, if your fabrics are really thin, you can add a strip of interfacing to the front coat pieces where your buttonholes and buttons will be. Cut two strips of fusible interfacing 1 inch wide. The length will depend on how many buttons and where you will place them. Fuse them to the wrong side of your front bodice pieces 1/2 an inch from the edge. I skipped this step too.*
Pin and sew shoulder seams. Press them open.
Open up the coat at the shoulder seam, right side up. Find the center of the sleeve and pin that to the shoulder seam, right sides together. Continue pinning the sleeve to the armhole carefully. Sew and press seam. Repeat with other sleeve.
Line up the side seams and the bottom of the sleeve, pin and sew (right sides together). Repeat with the other sleeve and side seam. Turn coat right side out and press.
Take your prepared collar and line up the center with the center of the back of the coat. You want the right sides of Fabric A to be facing up for both the collar and the coat when you lay them on top of each other like this. Pin the inner edge of the collar to the neckline of the coat. Baste the collar to the coat.
Repeat all of the steps with Fabric B (except for basting the collar).
To attach the two coats, lay Fabric A coat down, right side up.
Lay the Fabric B coat on top, right sides together. Sleeves should be on the inside. Pin the entire outer edge and sew together leaving about a 6-8″ opening along the bottom.
Pull the sleeves out.
Take one of the sleeves and fold it out (towards the wrong side) by about 1.5 inches. Slide it inside the other sleeve, line up the bottom seams of the sleeves and pin the ends of the sleeves together.
Sew the sleeves together along the pinned edge. Go slowly and untwist the coat to your left as you go along. Repeat with other sleeves.
Flip the coat right side out through the opening in the bottom. You’re almost done!! Press all the edges of the coat out. Hand sew the opening shut using a slip stitch. If you want, you can top stitch along the entire outer edge of the coat.
Sew your buttonholes where desired and attach your buttons. You’ll want to either use the same buttons on both sides or at least use the same size buttons. I sewed buttons to both sides of the coat at the same time using one thread.
Now your kiddo has two stylish coats in one!
I hope you guys are having fun with your bodice patterns and realizing all the endless possibilities a great pattern has. If you have any questions or just want to stop by and see what else I’ve been up to, please come visit me at you & mie!
Thanks so much for having me, Jen & Autie!